Gas burner clicks but won't light
We test the igniter, spark module, and gas valve with a multimeter, then replace the failed component. After the repair we leak-test the connection and confirm a clean blue flame on every burner before we leave.
Gas, electric, and induction cooktop repair done right the first time
Cooktop Repair Cupertino CA You Can Count On
When your cooktop quits, dinner plans change fast. Our cooktop repair Cupertino CA service gets your burners, igniters, and heating elements working again, usually the same day you call. We handle gas, electric, and induction models from Wolf, Thermador, Bosch, Samsung, and LG. Whether it's a gas cooktop not igniting or an induction unit throwing error codes, we diagnose it, fix it, and test every burner before we leave.
Careful work. Honest options.
About this service
Cooktop Repair Cupertino CA: What We Actually Do
Cooktop repair is the work of tracing why a burner, igniter, or control board stopped doing its job, then replacing or recalibrating the failed part so every zone heats on command. On a gas cooktop that means checking the igniter, spark module, gas valve, and burner cap alignment. On electric and induction units it means testing the heating element, thermostat, and control board with a multimeter and clamp meter. We carry the parts and tools to finish most repairs in one visit.
Cupertino homeowners call us for the same handful of failures: a gas burner that clicks but never lights, an induction zone that flashes an error and shuts off, or a control board that died after a power surge. Homes in Monta Vista and Rancho Rinconada tend to have older gas cooktops with worn igniters, while newer builds in Seven Springs often have built-in induction units with sensitive electronics. If you've been searching for cooktop repair near me Cupertino CA, we're local and we stock the common parts.
- ✓ Same-Day Repair Available
- ✓ All Cooktop Types Covered
- ✓ Upfront Pricing, No Surprises
- ✓ Licensed and Code-Correct
What's included
What Our Cooktop Repair Service Includes
Every cooktop repair visit includes a full diagnostic, the repair itself, and testing of every burner before we leave. Here's what's covered and what's available as an add-on when you book with us.
✓
Full Diagnostic Testing
We test the igniter, spark module, gas valve, heating element, thermostat, and control board with a multimeter and clamp meter. You get a clear explanation of what failed and why, plus a flat price for the fix before any work starts.
✓
Failed Part Replacement
We replace the failed component with a manufacturer-matched part. Igniters, spark modules, heating elements, thermostats, and control boards are stocked on the truck for most major brands, which is why most repairs finish in one visit.
✓
Gas Leak Testing
On gas cooktops we leak-test every connection with a leak detector after the repair. You get a clean blue flame and a safe connection, verified before we close up. This is code-required work and we do it on every gas job, no exceptions.
✓
Full Burner Verification
We run every burner through a complete heat cycle, checking ignition, flame quality, and temperature hold. On induction and electric units we confirm each zone reaches its set temperature. You see it working before we pack up our tools.
✓
Cleanup and Warranty
We wipe down the cooktop and surrounding counter, put the kitchen back the way we found it, and hand you a written warranty on parts and labor. If anything isn't right after the repair, you call us and we come back.
How it works
How Our Cooktop Repair Process Works
01
Call or Book
You call (669) 308-4259 or book online. We ask what's happening: which burner, what it's doing, and the brand and model. That five-minute conversation lets us load the right parts on the truck before we leave, which is why so many jobs finish in a single visit.
02
Diagnose On-Site
The technician arrives in a marked truck and gets to work. We pull the cooktop, test the igniter, spark module, gas valve, heating element, thermostat, and control board with a multimeter and clamp meter, then trace the fault to the exact failed component. Diagnosis takes 20 to 40 minutes on most models.
03
Quote and Approve
We show you what failed, explain the repair in plain language, and give you a flat price before any work starts. You approve it or you don't. If the cost of the repair doesn't make sense against a replacement, we'll say so. No pressure either way.
04
Repair and Test
We replace the failed part, reconnect the gas line or wiring, and test every burner through a full heat cycle. On gas units we leak-test the connection with a leak detector and confirm a clean blue flame. On induction and electric units we verify each zone reaches temperature and holds it.
05
Clean Up and Warranty
We wipe down the cooktop, put the kitchen back the way we found it, and walk you through what we fixed. You get a written warranty on parts and labor. Most repairs take 60 to 90 minutes on-site, and you're cooking on it the same day.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Multimeter
Tests continuity and voltage on igniters, heating elements, thermostats, and control boards to pinpoint the exact failed component.
Clamp Meter
Measures current draw on induction boards and electric elements, confirming whether a component is pulling power or has failed open.
Leak Detector
Sniffs for gas at every connection after a repair. Required on all gas cooktop work and used before we close up the unit.
Thermal Imaging Camera
Maps heat across the cooktop surface to find cold spots, uneven zones, and failing elements that a visual check would miss.
Screwdriver and Nut Driver Set
Pulls cooktop panels and burner assemblies without stripping screws or damaging trim on built-in units.
Wire Stripper and Pliers
Makes clean connections when replacing control boards, igniters, and heating elements, so the repair holds long-term.
Real results
Before and after.
Gas Cooktop Igniter Replacement in Monta Vista
Before
A homeowner in Monta Vista had a Wolf gas cooktop where two burners clicked but never lit. They'd been cooking on the two working burners for three weeks and were close to replacing the whole unit.
After
We diagnosed a failed spark module and a worn igniter on the front burner. Both were replaced in 70 minutes, and every burner lit on the first click. The homeowner spent $310 instead of $2,800 on a new cooktop.
Induction Control Board Repair in Seven Springs
Before
An induction cooktop in Seven Springs started flashing an error code and shutting off mid-boil. Two zones were dead, and the homeowner was using a portable hot plate while deciding what to do.
After
We isolated the fault to the induction power board using a clamp meter and thermal imaging camera. The board was replaced with a matched part, and all four zones reached temperature in testing. Total repair time was 95 minutes.
Electric Element Replacement in Rancho Rinconada
Before
An electric cooktop in Rancho Rinconada had one zone that wouldn't heat and another that heated unevenly, burning food on one side. The breaker had tripped twice in the past month.
After
We tested the heating element and thermostat with a multimeter and found a burned-out element plus a failing thermostat. Both were replaced in 80 minutes. All four zones now heat evenly, and the breaker has held since.
Problems we solve
Cooktop Problems We Fix in Cupertino
Most cooktop failures fall into a handful of categories, and we've fixed all of them. If you're dealing with a gas cooktop not igniting repair Cupertino California homeowners call about, or an induction unit that won't hold temperature, here's what we solve.
Ask a pro →↗
Induction zone flashes an error and shuts off
Induction faults usually trace to the power board, coil, or touch panel. We isolate the failed board with a clamp meter and thermal imaging camera, replace it with a matched part, and verify each zone reaches temperature.
Electric element won't heat or heats unevenly
We test the heating element, thermostat, and control board, then replace the failed part. After the repair we run each zone through a full heat cycle to confirm even temperature across the entire surface.
Control board dead after a power surge
We confirm the board is the fault, not the wiring or breaker, then replace it with a manufacturer-matched control board. Most boards for Samsung, LG, GE, and Whirlpool cooktops are stocked for same-day repair.
Transparent pricing
Cooktop Repair Cost in Cupertino
$180 - $650 depending on the failed part and cooktop type
Cooktop repair pricing in Cupertino depends on the part that failed, the brand, and how accessible the cooktop is. Most repairs run $180 to $450 in 2026, including the part and labor. A simple igniter or element swap sits at the low end, while a control board or induction module replacement lands higher. We quote a flat price before we start, so you're never surprised. If the repair costs more than the cooktop is worth, we'll tell you straight and help you weigh replacement.
A cooktop repair costs a fraction of replacing a built-in unit, which can run $1,500 to $4,000 installed. Most repairs we do cost less than 20% of a replacement, and the fix is warrantied. That's money well spent.
01Type of cooktop
Gas cooktops are usually the least expensive to repair because igniters and spark modules are simple parts. Electric cooktops sit in the middle. Induction cooktops cost more because the power boards and coils are expensive components.
02Failed component
An igniter or heating element replacement is a straightforward repair. A control board or induction module costs more because the part itself is expensive. We tell you which category your repair falls into before we start.
03Brand and model
Parts for Sub-Zero, Wolf, Viking, and Thermador units cost more than parts for GE, Whirlpool, or Frigidaire. High-end brands also take longer to access. We stock common parts for all these brands to keep the repair to one visit.
04Accessibility
A freestanding cooktop is easier to pull than a built-in unit surrounded by tight cabinetry. Built-in cooktops in Downtown Cupertino condos take longer to access, which adds labor time. We quote the access cost upfront.
Proof you can check
Licensed, Insured, and Warrantied
✓
California State Contractor License (C-38)California Contractors State License Board
✓
NATE CertificationNorth American Technician Excellence
✓
EPA Section 608U.S. Environmental Protection Agency
✓
UL Listed PartsUnderwriters Laboratories
✓
OSHA Safety ComplianceOccupational Safety and Health Administration
Customer reviews
What Cupertino Customers Say
★★★★★
“Our Wolf gas cooktop stopped igniting on two burners and we'd been putting off the repair for weeks. The technician showed up the same afternoon, diagnosed a failed spark module, and had it fixed in under an hour. He leak-tested everything and showed me the blue flame on each burner before he left. Fair price, no upsell.”
PM
Priya M.Homeowner, Monta Vista
✓ Verified“
★★★★★
“Induction cooktop started throwing an error code and shutting off mid-boil. I called Same Day Appliance Repair Cupertino and they came out the next morning. Turned out to be a control board issue. They had the part on the truck and finished the repair in about 75 minutes. Kitchen's been working perfectly since.”
DL
David L.Homeowner, Rancho Rinconada
✓ Verified★★★★★
“Our electric cooktop had one zone that wouldn't heat at all. The technician tested the element and thermostat with a multimeter, found a burned-out element, and replaced it on the spot. He was clean, polite, and explained what went wrong. Cost was right in the range they quoted on the phone. I'd call them again.”
SK
Susan K.Homeowner, Seven Springs
✓ VerifiedMost cooktop repairs in Cupertino run $180 to $450 in 2026, including the part and labor. A simple igniter swap sits at the low end, while a control board or induction module replacement lands higher. We quote the exact price before we start, so there's no surprise on the invoice. If the repair costs more than a replacement makes sense, we'll tell you.
The most common cause is a worn or wet igniter, followed by a failed spark module or a clogged burner cap. If you hear clicking but see no flame, the spark is firing but the gas isn't reaching it, which usually means a blocked burner port or a bad gas valve. We test each component with a multimeter and leak detector, then replace the failed part and confirm a clean blue flame on every burner.
Yes. We repair induction cooktops from Bosch, Thermador, Wolf, Samsung, LG, and GE, including error-code faults, dead zones, and control board failures. Induction units are electronics-heavy, so we test the power board, coil, and touch panel with a clamp meter and thermal imaging camera to isolate the fault. Most induction repairs finish in one visit because we stock the common boards.
Most cooktop repairs take 60 to 90 minutes on-site once the technician arrives. Diagnosis runs 20 to 40 minutes, and the repair itself is usually 30 to 60 minutes depending on the part. If we have to order a specialty board for a Sub-Zero or Viking unit, it can take two to four days. We'll tell you the timeline upfront.
More services
Related Appliance Repair Services
Refrigerator RepairIf your fridge is warm and your cooktop is down, it's been a rough week. We repair refrigerator not cooling, compressor, condenser coil, and door gasket faults on the same visit, so you get one trip and one invoice for both kitchen problems.Explore →
Freezer RepairA freezer that won't hold temperature can ruin hundreds of dollars of food. We diagnose thermostat, evaporator coil, and compressor faults and get your freezer back to 0°F. Book it alongside cooktop repair and we'll handle both in one appointment.Explore →
Ice Maker RepairIce makers fail on water inlet valve, fill tube, and control board problems. If your ice maker stopped producing while your cooktop was also acting up, we can fix both in a single visit. We stock common valves and boards for Samsung, LG, Whirlpool, and GE units.Explore →
Washer RepairWasher not draining or spinning? We repair drain pump, control board, and door gasket faults on top-load and front-load machines. Cupertino customers often bundle washer repair with cooktop service to get the whole house running in one appointment.Explore →
Dryer RepairA dryer not heating is usually a failed heating element, thermostat, or thermal fuse. We test each component and replace the failed part the same day. Pair it with cooktop repair and we'll knock out both appliances in one trip.Explore →
Washer and Dryer Combo RepairStackable and combo units pack a lot into a small footprint, and when they fail, both functions often go at once. We repair combo washer-dryer units in Cupertino condos and apartments, handling drain pump, heating element, and control board faults in a single visit.Explore →
Dishwasher RepairDishwasher leaking or not draining? We fix water inlet valve, drain pump, and door gasket problems. If your kitchen is already torn apart for cooktop repair, it's a smart time to get the dishwasher checked too. One technician, one visit.Explore →
Oven RepairOven not heating usually means a failed heating element, igniter, or thermostat. We repair gas and electric ovens from Wolf, Thermador, GE, and Whirlpool. Bundle it with cooktop repair and we'll service both in one appointment, saving you a second trip charge.Explore → Ready when you are
Book Cooktop Repair Cupertino CA Today
Call (669) 308-4259 and we'll get a technician to your kitchen, often the same day. We're licensed, insured, and we warranty every cooktop repair we do. One call and your burners are back.
Book Repair Now (669) 308-4259 →
Request an appointment
Contact Us for Appliance Repair
Call us at (669) 308-4259 or email info@samedayappliancerepaircupertino.com to book your appliance repair. We answer calls seven days a week and offer same-day appointments across Cupertino. Most calls are scheduled within two hours.
Call anytime(669) 308-4259Email the officeinfo@samedayappliancerepaircupertino.online
Office hoursOpen 24 hours · 7 days a week